Nissan

nissan


NISSAN NAVARA 1998-2002-- 2003-2004

nissan

 

CALMINI SOLID AXLE SWAP SYSTEM
nissan

If you are ready to take your Frontier to the next level, this is the only system that can take it there.  We are happy to release the first kit of its kind for Nissan vehicles, the CALMINI Solid Axle Swap.  This kit is over 85% bolt-on with the only welding to occur on the donor axle.   Our complete system allows for the entire removal of the stock IFS system and a full replacement, with a full center skid, with a solid axle out of an early model Jeep Wagoneer.  The donor axle this kit is designed for is out of a 1980-85 Jeep Wagoneer model Dana 44 (D44), with a driver's side drop and a non-vacuum actuated disconnect. 

CALMINI 4WD 3" SUSPENSION LIFT
nissan


The ultimate rockcrawling and off-road performance suspension for the 4WD Frontier Pickup.  Featured in our system are our signature plate style upper control arms which allow for factory alignment after the lift is installed.  Also included in the kit are CALMINI heavy duty torsion bars with a higher than stock spring rate to allow for a higher lift with a comfortable ride.  The complete suspension system also includes Vecton control arm bushings, sleeves, new ball joints, laser cut shackles and hardware, rear lift blocks, rear brake line extension brackets and spacers, CALMINI performance shocks, complete hardware, and installation instructions. 

 

NISSAN NAVARA 2005-2010

Suspension

 

CALMINI 5" SUSPENSION SYSTEM

nissan


Nissan Frontier 5” Performance Suspension System
CALMINI Products all new Nissan Frontier 5" 4WD lift system is now available. Constructed using laser crafted components, these kits utilize the most modern manufacturing techniques found in today’s suspension systems. Our systems include new replacement cast steering knuckles, front differential drop brackets to correct pinion angle, and easy to install 1 piece MIG-welded subframes. Standard equipment includes a heavy duty center skid plate that bolts to the lower subframe for increased strength and protection, extended front and rear stainless steel brake lines, and rear Monotube Gas Shocks w/boots. Powdercoat finish, and top quality plated hardware provides corrosion resistance, and long service life.



CALMINI BLOCK SUSPENSION SYSTEM 2.5’’

nissan


This CALMINI suspension kit will lift the Frontier by 2-2.5" over stock.  The complete kit consists of machined aluminum spacers finished in a high quality blue anodized finish with laser marking, rear lift blocks, and the complete replacement u-bolt kit. This system will allow for increased articulation and ground clearance.  Vehicle will require a front end alignment once the kit is installed.

 

1986.5-97 Hardbody D21 4WD

CALMINI 3" SUSPENSION SYSTEM
nissan
nissan


The only complete suspension system for your 4WD Hardbody pickup.  Our full system features our signature plate upper control arms which allow for correct factory alignment.  This is the system to bring your tired pickup back to life.  The complete system includes new laser crafted upper control arms, Vecton bushings, sleeves, new upper ball joints, new 27.5mm heavy duty torsion bars, rear lift blocks, laser cut shackles, new rear U-bolts, brake line stand-off kit, complete hardware and CALMINI performance shocks.  Kits also comes complete with installation instructions.

 

Xterra Suspension Components 2000-2004

nissan

 

CALMINI SOLID AXLE SWAP SYSTEM
nissan

If you are ready to take your Xterra to the next level, this is the only system that can take it there.  We are happy to release the first kit of its kind for Nissan vehicles, the CALMINI Solid Axle Swap.  This kit is over 85% bolt-on with the only welding to occur on the donor axle.   Our complete system allows for the entire removal of the stock IFS system and a full replacement, with a full center skid, with a solid axle out of an early model Jeep Wagoneer.  The donor axle this kit is designed for is out of a 1980-85 Jeep Wagoneer model Dana 44 (D44), with a driver's side drop and a non-vacuum actuated disconnect. 

 

CALMINI  3" SUSPENSION LIFT
nissan

This complete kit is built and designed for the Xterra.  Featured in our system are our signature plate style upper control arms, featuring grease zerks, which allow for factory alignment after the lift is installed.  Also included in the kit are CALMINI heavy duty torsion bars and our add-a-leaf system to help smooth out the ride and increase payload capacity.  The complete suspension system also includes Vecton control arm bushings, sleeves, new ball joints, laser cut precision bent shackles and hardware, rear sway bar links, bump stop extensions, CALMINI performance shocks, complete hardware, and installation instructions.  This is the ultimate suspension system for your Xterra and can handle anything from daily driving, mild trail riding, and extreme rockcrawling situations.



Copyright © 2008 -Yiannis Kalivitis
All Rights Reserved
Email:
kalivitis@cytanet.com.cy